Thank you for visiting our website. Your personal privacy is absolutely respected and protected by the website. To help you understand how the website collects, uses and protects your personal information, be sure to read the website "Privacy Policy". Thank you!
ACCEPT AND PROCEED
RSSRSS

Products

35MHz Oscilloscope Differential Probe
Home  ›   Products  ›  Oscilloscope Probes

35MHz Oscilloscope Differential Probe

35MHz Oscilloscope Differential Probe

 

 facebook
Product ID: DP-35

 Differential Probe  for Oscilloscope  

DP-35 ( 35MHz /1600 Vp-p / >=10mV )


DP-35   35 MHz Differential Probes for Oscilloscopes
Separating Design(Standard No.114205) Convenient & Durable.

 




SPECIFICATIONS:
(1) Bandwidth:
DC - to 35 MHz (-3 dB) for x 100
DC - to 25 MHz (for attenuation x 10)
(2) Attenuation: x 10, or x 100
(3) Accuracy: +/- 2%
(4) Voltage Input Ranges (DC + AC peak to peak):
≦ 160 Vp-p for x 10, (i.e about 56 V RMS or ± 80 V DC)
≦ 1600 Vp-p for x 100, (i.e about 560 V RMS or ± 800 V DC)
(5) Permitted Max Input Voltage
Max differential voltage: 1600 V (DC + AC peak to peak)
Max voltage between each input terminal and ground: 600 V RMS
(6) Input Impedance:
Differential: 9 MΩ // 1.7 pF
Between terminals and ground: 4.5 MΩ // 3.4 pF
(7) Output:  ± 8.0 V
(8) Output Impedance: 50 Ω
(9) Rise Time: 10 ns for x 100; 14 ns for x 10
(10) Rejection Rate on Common Mode:
60 Hz: >80 dB ; 100 Hz: >60 dB ; 1 MHz: >50 dB
(11) Power Supply:
External 9 V DC power supply.
(12) Consumption: 200 mA about (9 V DC)
 

Specifications:
  • FEATURES
    • FEATURES
    • The DP-25 FET input differential probe provieds a safe means of measuring circuits with floating potentials up to 1000 V ( DC+ peak AC ) from ground and 1300V ( DC + peak AC ) differential.
    • The DP-25 converts the high voltage differencial input signal to a low voltage ground refereced signal for display on any Oscilloscope.
    • The output BNC of DP-25 is calibrted to drive a high impedance ( 1M Ohm) load.
    • INSTRUCTION FOR USE
    • Connect the output BNC of DP-25 to the input BNC of the Oscilloscope by the accessory BNC cable.
    • Adjust the vertical offset of the Oscilloscope if necessary.
    • Set the select proper range of the DP-25 and the V / DIV of the Oscilloscope according to the scale conversion chart.
    • Scale conversion chart : The effective V / DIV is the attenuation factor of x 20, x 50, x 200 multiplied by the scale factor of the Oscilloscope. It will be twice when the 50 Ω load was used. For example, with the range set at x 200,
    • and the scope set to 0.5 V / DIV, the effective V / DIV equals 200 x 0.5 or 100 V, with the 50 Ohm load was used, it becomes 200V, the power consumption will increase too.
    • NOTE:If the voltage of the input signal exceeeds the linear range of the setting range.The signal output of
    • the DP-25 would not accurately, the wave form display will be cut off.
  • WARNING
    • WARNING
    • Do not use DP-25 above 1000v ( DC + peak AC ) between ground and the input or 1,300V ( DC + peak AC ) between the input lead.
    • Do not operate DP-25 in wet or damp condition.
    • Do not operate DP-25 in an explosive atmosphere.
    • Do not immerse DP-25 in liquids.
    • Do not operated DP-25 without covers.
    • Please change the battery when the "LOW BATT " LED is lighted. At this time DP-25 can operate but not guaranteed the accuracy.
    • DP-25 can not operate if both POWER and LOW BATT LED are not light.
    • FEATURES
    • The DP-25 FET input differential probe provieds a safe means of measuring circuits with floating potentials up to 1000 V ( DC+ peak AC ) from ground and 1300V ( DC + peak AC ) differential.
    • The DP-25 converts the high voltage differencial input signal to a low voltage ground refereced signal for display on any Oscilloscope.
    • The output BNC of DP-25 is calibrted to drive a high impedance ( 1M Ohm) load.
    • INSTRUCTION FOR USE
    • Connect the output BNC of DP-25 to the input BNC of the Oscilloscope by the accessory BNC cable.
    • Adjust the vertical offset of the Oscilloscope if necessary.
    • Set the select proper range of the DP-25 and the V / DIV of the Oscilloscope according to the scale conversion chart.
    • Scale conversion chart : The effective V / DIV is the attenuation factor of x 20, x 50, x 200 multiplied by the scale factor of the Oscilloscope. It will be twice when the 50 Ω load was used. For example, with the range set at x 200,
    • and the scope set to 0.5 V / DIV, the effective V / DIV equals 200 x 0.5 or 100 V, with the 50 Ohm load was used, it becomes 200V, the power consumption will increase too.
    • NOTE:If the voltage of the input signal exceeeds the linear range of the setting range.The signal output of
    • the DP-25 would not accurately, the wave form display will be cut off.
Features:
Certificate:
  • CE

Contact Detail

Contact:Stanley Hwang
Address: 3F., No.12, Lane. 130, MinQuan Road., XinDian Dist., New Taipei City 23141, TAIWAN
TEL:886-2-2218-3111
FAX:台灣-2-2218-3222
Email:tecpelco@gmail.com
URL:http://www.tecpel.com
http://www.tecpel.com.tw
ZIP:23141