RSSRSS

Products

High Voltage Oscilloscope Probe / Differential Probe
Home  ›   Products  ›  Oscilloscope Probes

High Voltage  Oscilloscope  Probe / Differential Probe

High Voltage Oscilloscope Probe 50 MHz HVP-15HF

High Voltage  Oscilloscope  Probe / Differential Probe

Differential Probe DP-25

 facebook
Download Now !
Product ID: HVP-15HF / DP-25

High Voltage & High Frequency Oscillosocpe Probe

Model: HVP-15HF

Specification:
Max. Working Voltage:
DC: 0 ~ 10KV DC
AC: Pulse < 30KV Peak to Peak
AC: Sine Ware < = 10KV rms

Singal / Noise :
> =60 dB( 1KHZ), > = 50dB (1MHz)
Bandwidth: DC ~ 50MHz ( -3dB)
Division Ration: 1: 100
Rise Time < = 7ns

Input Resistance : 100M Ohm +/- 0.5%

Input Capacitance : 3.0 PF +/- 0.5 PF
Compensation Range : 5 PF~ 50 PF
Cable Length: 2.0 Meter (+/- 0.2M)
Temperature Cofficient: DC Accuracy: < = 0.7%
Safety Approval : CE, GS, UL, CUL
Operating Temperature: 0 ~ 50 Degree C.
Storage Temperature : -20 ~ 70 Degree C/
Weight : 250 g
Dimension: 75 Dia * 340 mm Length

--------------------------------------------
DP-25 Differential Probe
3 RANGE ATTENUATOR.
2 POWER SOURCE.
1000V INPUT CAT III
LOW BATT. AUTO OFF.
SEPARATING DESIGN.CONVENIENT, DURABLE.
MEET CE, IEC 1010, EN 61010, UL 3111.
Band width (-3dB, 50Ω load): DC-25MHz . ( x 20: DC~15MHz)
Accuracy : ± 2% at 20-30°C 70% RH after 20 minutes warm up.
Attenuation : x 20, x 50, x 200 ( Into 1M Ohm scope ) ; x 40, x 10
, x 400 ( Into 50 Ohm load )
Maximum operation Voltage ( DC + peak AC ) :
Maximum input Differential Voltage : 1300V ( DC + peak AC ) or 1000V RMS
Maximum input Voltage to Ground : 1000V ( DC + peak AC ) or 600V RMS
Common Mode Rejection Ratio ( CMRR ):
60Hz : >10,000 : 1
100Hz: >1,000 : 1
1MHz: > 300 : 1
Noise : Input Impedance :
2M Ohm, 2.3 PF between inputs and ground.
4M Ohm, 1.2 PF between inputs.
Power :One internal 9V alkaline battery or external 6V-9V DC.

WARNING

Do not use DP-25 above 1000v ( DC + peak AC ) between ground and the input or 1,300V ( DC + peak AC ) between the input lead.
Do not operate DP-25 in wet or damp condition.
Do not operate DP-25 in an explosive atmosphere.
Do not immerse DP-25 in liquids.
Do not operated DP-25 without covers.
Please change the battery when the "LOW BATT " LED is lighted. At this time DP-25 can operate but not guaranteed the accuracy.
DP-25 can not operate if both POWER and LOW BATT LED are not light.
FEATURES


The DP-25 FET input differential probe provieds a safe means of measuring circuits with floating potentials up to 1000 V ( DC+ peak AC ) from ground and 1300V ( DC + peak AC ) differential.
The DP-25 converts the high voltage differencial input signal to a low voltage ground refereced signal for display on any Oscilloscope.
The output BNC of DP-25 is calibrted to drive a high impedance ( 1M Ohm) load.
INSTRUCTION FOR USE


Connect the output BNC of DP-25 to the input BNC of the Oscilloscope by the accessory BNC cable.
Adjust the vertical offset of the Oscilloscope if necessary.
Set the select proper range of the DP-25 and the V / DIV of the Oscilloscope according to the scale conversion chart.
Scale conversion chart : The effective V / DIV is the attenuation factor of x 20, x 50, x 200 multiplied by the scale factor of the Oscilloscope. It will be twice when the 50 Ω load was used. For example, with the range set at x 200,
and the scope set to 0.5 V / DIV, the effective V / DIV equals 200 x 0.5 or 100 V, with the 50 Ohm load was used, it becomes 200V, the power consumption will increase too.
NOTE:If the voltage of the input signal exceeeds the linear range of the setting range.The signal output of
the DP-25 would not accurately, the wave form display will be cut off.

Features:
Certificate:
  • CE

Contact Detail

Contact:Stanley Hwang
Address:11F, NO. 182, DUNHUA SOUTH ROAD, SEC. 2, DA'AN DISTRICT 10669 TAIPEI, TAIWAN
TEL:886-2-27375866
FAX:台灣-2-27373343
Email:tecpelco@gmail.com
URL:http://www.tecpel.com
http://www.tecpel.com.tw
ZIP:10669