Thank you for visiting our website. Your personal privacy is absolutely respected and protected by the website. To help you understand how the website collects, uses and protects your personal information, be sure to read the website "Privacy Policy". Thank you!
ACCEPT AND PROCEED
RSSRSS

Products

High Voltage Differential Probe 25MHz
Home  ›   Products  ›  Oscilloscope Probes

High Voltage Differential Probe 25MHz

25MHz High Voltage Differential Probe for oscilloscope

 

 facebook
Product ID: DP-25

. The DP-25 High Voltage Differential probe provides a safety means for measuring differential voltage to all models of oscilloscope.  The DP-25 coverts the high differential voltage (<=1400 Vpeak) into a low voltage (<=7.0v, with reference to the earth) and display on the oscilloscopes.  The DP-25 is designed to operate with the 1M Ohm impedance oscilloscope. When combine with the 50 Ohm load, the attenuation will be 2 times. We recommend to use Tecpel PL-10 with DP-25 to expand the measuring with Digital multimeter (DMM) to observe more accurate measurement. The accuracy of oscilloscope is 3% and the DMM is less than 1%. Note: If you connect DP-25 to the DMM without Tecpel PL-10 the accuracy will be higher than 10%.

Specifications:
  • FEATURES
    •  The DP-25 FET input differential probe provieds a safe means of measuring circuits with floating potentials up to 1000 V ( DC+ peak AC ) from ground and 1300V ( DC + peak AC ) differential.
    • The DP-25 converts the high voltage differencial input signal to a low voltage ground refereced signal for display on any Oscilloscope.
    • The output BNC of DP-25 is calibrted to drive a high impedance ( 1M Ohm) load.
    • INSTRUCTION FOR USE
    • Connect the output BNC of DP-25 to the input BNC of the Oscilloscope by the accessory BNC cable.
    • Adjust the vertical offset of the Oscilloscope if necessary.
    • Set the select proper range of the DP-25 and the V / DIV of the Oscilloscope according to the scale conversion chart.
    • Scale conversion chart : The effective V / DIV is the attenuation factor of x 20, x 50, x 200 multiplied by the scale factor of the Oscilloscope. It will be twice when the 50 Ω load was used. For example, with the range set at x 200,
    • and the scope set to 0.5 V / DIV, the effective V / DIV equals 200 x 0.5 or 100 V, with the 50 Ohm load was used, it becomes 200V, the power consumption will increase too.
    • NOTE:If the voltage of the input signal exceeeds the linear range of the setting range.The signal output of
    • the DP-25 would not accurately, the wave form display will be cut off.
  • WARNING
    • WARNING
    • Do not use DP-25 above 1000v ( DC + peak AC ) between ground and the input or 1,300V ( DC + peak AC ) between the input lead.
    • Do not operate DP-25 in wet or damp condition.
    • Do not operate DP-25 in an explosive atmosphere.
    • Do not immerse DP-25 in liquids.
    • Do not operated DP-25 without covers.
    • Please change the battery when the "LOW BATT " LED is lighted. At this time DP-25 can operate but not guaranteed the accuracy.
    • DP-25 can not operate if both POWER and LOW BATT LED are not light.
    • FEATURES
    • The DP-25 FET input differential probe provieds a safe means of measuring circuits with floating potentials up to 1000 V ( DC+ peak AC ) from ground and 1300V ( DC + peak AC ) differential.
    • The DP-25 converts the high voltage differencial input signal to a low voltage ground refereced signal for display on any Oscilloscope.
    • The output BNC of DP-25 is calibrted to drive a high impedance ( 1M Ohm) load.
    • INSTRUCTION FOR USE
    • Connect the output BNC of DP-25 to the input BNC of the Oscilloscope by the accessory BNC cable.
    • Adjust the vertical offset of the Oscilloscope if necessary.
    • Set the select proper range of the DP-25 and the V / DIV of the Oscilloscope according to the scale conversion chart.
    • Scale conversion chart : The effective V / DIV is the attenuation factor of x 20, x 50, x 200 multiplied by the scale factor of the Oscilloscope. It will be twice when the 50 Ω load was used. For example, with the range set at x 200,
    • and the scope set to 0.5 V / DIV, the effective V / DIV equals 200 x 0.5 or 100 V, with the 50 Ohm load was used, it becomes 200V, the power consumption will increase too.
    • NOTE:If the voltage of the input signal exceeeds the linear range of the setting range.The signal output of
    • the DP-25 would not accurately, the wave form display will be cut off.
Features:

Product ID: DP-25
25MHz Differential Probe
3 RANGE ATTENUATOR.
2 POWER SOURCE.
1000V INPUT CAT III
LOW BATT. AUTO OFF.
SEPARATING DESIGN.CONVENIENT, DURABLE.
MEET CE, IEC 1010, EN 61010, UL 3111.
Band width (-3dB, 50Ω load): DC-25MHz . ( x 20: DC~15MHz)
Accuracy : +/- 2% at 20-30'C 70% RH after 20 minutes warm up.
Attenuation : x 20, x 50, x 200 ( Into 1M Ohm scope ) ; x 40, x 10
, x 400 ( Into 50 Ohm load )
Maximum operation Voltage ( DC + peak AC ) :
Maximum input Differential Voltage : 1300V ( DC + peak AC ) or 1000V RMS
Maximum input Voltage to Ground : 1000V ( DC + peak AC ) or 600V RMS
Common Mode Rejection Ratio ( CMRR ):
60Hz : >10,000 : 1
100Hz: >1,000 : 1
1MHz: > 300 : 1
Noise : Input Impedance :
2M Ohm, 2.3 PF between inputs and ground.
4M Ohm, 1.2 PF between inputs.
Power :One internal 9V alkaline battery or external 6V-9V DC.

Certificate:
  • CE

Contact Detail

Contact:Stanley Hwang
Address: 3F., No.12, Lane. 130, MinQuan Road., XinDian Dist., New Taipei City 23141, TAIWAN
TEL:886-2-2218-3111
FAX:台灣-2-2218-3222
Email:tecpelco@gmail.com
URL:http://www.tecpel.com
http://www.tecpel.com.tw
ZIP:23141