TECPEL Co., Ltd.

Specifications:

• LCR200 SPECIFICATIONS:
  • Test Condition :
  • Frequency : 100Hz / 120 Hz / 1KHz / 10KHz / 100KHz / 200KHz
  • Level : : 1Vrms / 250m Vrms / 50m Vrms / 1Vdc (DCR only)
  • Measurement Parameters : : Z, Ls, Lp, Cs, Cp, DCR, ESR, D, Q and Theta
  • Basic Accuracy : : 0.1 %
  • Dual Liquid Crystal Display with LED backlit
  • Auto Range or Range Hold selection
  • Open / Short Calibration
  • RS232C Interface
  • Primary Parameters Display
  • Z : AC Impedance
  • DCR : DC Resistance
  • Ls : Serial Inductance
  • Lp : Parallel Inductance
  • Cs : Serial Capacitance
  • Cp : Parallel Capacitance
  • Secondary Parameters Display
  • (Theta) : Angle Impedance
  • ESR : Equivalent Series Resistance
  • D : Dissipation Factor
  • Q : Quality Factor
  • Combinations of Display
  • Serial Mode : Z-Theta, Cs-D, Cs-Q, Cs-ESR, Ls-D, Ls-Q, Ls-ESR
  • Parallel Mode : Cp-D, Cp-Q, Lp-D, Lp-Q
  • DMM Functionalities:
  • DCV, ACV, DCA, ACA, Diode/Continuity Check
  • Measurement Range
  • Parameter Range
  • Z 0.000 Ohm to 500.0 M Ohm
  • L 0.030 micro H to 9999 H
  • C 0.003 pF to 80.00 mF
  • DCR 0.000 Ohm to 500.0 M Ohm
  • ESR 0.000 Ohm to 9999 Ohm
  • D 0.000 to 9999
  • Q 0.000 to 9999
  • Theta: -180.0 degree to 180.0 degree
  • V 0.000mV to +/- 600.0 V
  • I 0.000mA to +/- 2.000 A
  • DC Voltage Measurement:
  • Range : 2V, 20V, 200V, and 600V
  • Resolution : 1mV, 10mV, 100mV,1V
  • Accuracy : +/-(0.4 %+3Digit)
  • Input Impedance : 1M Ohm
  • AC Voltage Measurement ( True RMS ):
  • Range : 2V, 20V, 200V, and 600V
  • Resolution : 1mV, 10mV, 100mV, 1V
  • Accuracy : +/- (0.8%+5Digit) @ 40Hz~1KHz
  • Input Impedance : 1M Ohm
  • DC Current Measurement:
  • Range : 2A, 0.2A, 20mA and 2mA
  • Resolution : 1mA, 0.1mA, 0.01mA and 1 micro A
  • Accuracy : ±(0.4%+3Digit)
  • Input Impedance: 0.1 ohm @ current > 20mA , 10 Ohm @ current< or = 20mA
  • AC Current Measurement ( True RMS ):
  • Range : 2A, 0.2A, 20mA and 2mA
  • Resolution : 1mA, 0.1mA, 0.01mA and 1 micro A
  • Accuracy : +/- (0.8%+5Digit) @ 40Hz~1KHz
  • Input Impedance : 0.1 ohm @ current > 20mA , 10 Ohm @ current < or = 20mA
  • Continuity Check :
  • Continuity Threshold : 50 Ohm ( Approximately )
  • Continuity Indicator : Tone Buzzer
  • Input Protection : 600V ( max )
  • Diode Test: Test current : 2.5mA ( Typical )
  • Open circuit voltage : 5.0VDC ( nominal)
  • Input Protection : 600V ( max )
  • General:
  • Temperature : 0 to 40 deg C ( Operating ) -20 to 70 deg C ( Storage )
  • Reative Humidity : Up to 85%
  • AC Power : 110V / 220V +/- 10%, 60 / 50 Hz
  • Dimensions : 300mm x 220mm x 150mm (11.8" x 8.7" x 5.9" ) (DxWxH)
  • Weight : 4.5kgsStandard Accessories:
  • (1) TL09C KelvinClip : 1pc
  • (2) Test leads : 1pc
  • Optional Accessories:
  • (3) TL09A SMD test probe
  • (4) TL09B Component fixture

Features:

Certificate:

• CE